Home » Service & Support » Technical Documentation
Masoneilan 496 Position Switches & Transmitters - Technical Data & Applications
Release time:2026-11-23 01:35:36 | Views:

According to the Masoneilan official fact sheet (GEA19703), the 496 Series consists of position switches and transmitters that indicate control valve travel, rather than valve positioners. It combines on-off and continuous detection in one device and can be mounted on rotary valves such as Camflex II, MiniTork II and V-Max, and linear valves such as series 21000 and 41005. This article follows the manual on detection methods, materials, the European and US numbering systems and selection boundaries.

I. Product Positioning

ItemDescription
BrandMasoneilan (now part of Baker Hughes, formerly GE Oil & Gas)
Series496 Series Position Switches and Transmitters
FunctionIndicates control valve travel; on-off and continuous detection can be combined
Body / cover materialEpoxy-painted anodized aluminum
Protection certificationExplosion-proof, dust-tight and weatherproof to ATEX 94/9/EC; some models intrinsically safe
DocumentFact sheet GEA19703, 2012-07

Source: Masoneilan 496 Series Position Switches and Transmitters fact sheet, document GEA19703 (2012-07). Contact ratings, voltage levels, accuracy and full ingress ratings are not listed in the fact sheet; subject to the full catalog or manufacturer confirmation.

The name is easily misread as "positioner": the 496 is actually a feedback device that converts valve travel into switch contacts or a continuous electrical signal for the control system; it does not drive the actuator for positioning. It is a separate product, not interchangeable with the SVI digital positioners or the Type 78 air set.

Masoneilan digital positioner, illustration
Masoneilan digital positioner, illustration only, not the actual 496; parameters subject to the official catalog

II. Detection Methods and Applicable Valves

Detection typeMethodFeature
On-offMicro switch or proximity detectorDiscrete position signal, single or multiple points
ContinuousOpto-electronic transmitter (European) / potentiometric (US)Continuous signal proportional to travel
CombinedBoth functions can be combined in one deviceContinuous feedback plus limit contacts
Key benefitProximity detector and opto-electronic unit have no mechanical contactResistant to vibration and electrical noise, low friction, long life

Source: Masoneilan 496 Series Position Switches and Transmitters fact sheet, document GEA19703 (2012-07). Contact ratings, voltage levels, accuracy and full ingress ratings are not listed in the fact sheet; subject to the full catalog or manufacturer confirmation.

Valve categoryApplicable models
Rotary valvesCamflex II, MiniTork II, V-Max
Linear valvesSeries 21000, 41005

Source: Masoneilan 496 Series Position Switches and Transmitters fact sheet, document GEA19703 (2012-07). Contact ratings, voltage levels, accuracy and full ingress ratings are not listed in the fact sheet; subject to the full catalog or manufacturer confirmation.

III. European Design Numbering

FieldCodeMeaning
a Instrument type1One electromechanical switch, single-pole double-throw (SPDT)
a Instrument type2Two electromechanical switches, SPDT
a Instrument type4 / 5One / two proximity detector switches
a Instrument type6 / 7One / two electromechanical switches, double-pole double-throw (DPDT)
a Instrument type8Opto-electronic position transmitter
b Protection55Weatherproof
b Protection57Explosion-proof and weatherproof (ATEX)
b Protection58Intrinsically safe and weatherproof (ATEX)
c Additional switch1 / 2 / 4 / 5 / 6 / 7Only for 496-8 transmitter models, prefixed with a slash "/"

Source: Masoneilan 496 Series Position Switches and Transmitters fact sheet, document GEA19703 (2012-07). Contact ratings, voltage levels, accuracy and full ingress ratings are not listed in the fact sheet; subject to the full catalog or manufacturer confirmation.

The European template is 496-[a][b]/[c]. Example: 496-857 means opto-electronic transmitter (a=8), explosion-proof and weatherproof (b=57); 496-857/2 adds two SPDT switches (c=2). The source notes that an omitted protection field defaults to explosion-proof and weatherproof, but when b is omitted the default must be confirmed with the manufacturer.

IV. US Design Numbering

CodeMeaning
1One electromechanical switch, SPDT
2Two electromechanical switches, SPDT
3Potentiometric position transmitter
6One electromechanical switch, DPDT
7Two electromechanical switches, DPDT

Source: Masoneilan 496 Series Position Switches and Transmitters fact sheet, document GEA19703 (2012-07). Contact ratings, voltage levels, accuracy and full ingress ratings are not listed in the fact sheet; subject to the full catalog or manufacturer confirmation.

The US template has only the field 496-[a], the instrument type code; there is no protection field b and no additional switch field c. The continuous transmitter uses a potentiometric element (code 3) in the US design instead of the European opto-electronic element (code 8) - a key difference between the two systems.

V. Comparison of the Two Systems and Selection Notes

DimensionEuropean 496-ab/cUS 496-a
Instrument type options1,2,4,5,6,7,81,2,3,6,7
Continuous transmitterOpto-electronic (code 8)Potentiometric (code 3)
Proximity detectorYes (code 4/5)No
Protection field bYes (55/57/58)No
Additional switch field cYes (496-8 only, with "/")No
Field structure496 - a b / c496 - a

Source: Masoneilan 496 Series Position Switches and Transmitters fact sheet, document GEA19703 (2012-07). Contact ratings, voltage levels, accuracy and full ingress ratings are not listed in the fact sheet; subject to the full catalog or manufacturer confirmation.

The manual warns that some of the many combinations may not be available, or may not fully meet all protection standards; confirm with the manufacturer. Select the European or US design first, then fill in each field by required switch quantity/type, whether a continuous transmitter is needed, and the protection level. Contact ratings, voltage levels, temperature range, accuracy and IP rating are not in this fact sheet and must not be invented - consult the full catalog or the manufacturer.

Selection guide: The 496 is a position switch/transmitter, not a positioner: decide European (496-ab/c) or US (496-a) design first, then pick the instrument type code by on-off/continuous detection needs, then select field b by area protection and add field c switches as needed. Contact ratings, voltage, accuracy and protection levels are not given in the fact sheet - please consult for confirmation.

Common models: Common combinations include 496-857 (opto-electronic transmitter, explosion-proof and weatherproof) and 496-857/2 (with two SPDT additional switches); switch-only versions are 496-1, 496-2, 496-4/5 and 496-6/7 (European), with 496-1/2/3/6/7 in the US design.

If a model marked "496" leaves you unsure whether it is a position switch, a transmitter or a positioner, or you want to confirm the European/US code and protection field, please send us the nameplate and the site feedback requirement. We can work against GEA19703 to confirm the instrument type and field structure.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.