Home » Service & Support » Technical Documentation
Scotch Yoke Pneumatic Actuators - Working Principle & Features
Release time:2026-11-22 09:38:23 | Views:

A scotch yoke pneumatic actuator converts linear piston motion into 90 degree rotation through a slotted yoke driven by a pin. Its torque peaks at the two ends of travel and is lowest at mid-stroke, which matches valves whose break and seating torque is high while running torque is low, such as ball and plug valves. It therefore dominates large-bore and pipeline ESD duties. This article explains the principle, torque curve and selection points, with web-derived data sourced in place.

I. Product Positioning

ItemDescription
Product nameScotch Yoke Pneumatic Actuator
ConstructionA piston rod drives a slotted yoke; a pin sliding in the slot rotates the output shaft; single piston or twin opposed pistons
Torque characteristicU-shaped: peaks at 0 and 90 degrees, minimum near 45 degrees; peak-to-minimum ratio typically about 1.4-1.6 to 1
Typical serviceLarge ball valves, plug valves, gate valves, pipeline ESD valves; duties needing high opening and seating torque
SourceFisher G series (Emerson/Bettis, formerly Robotarm II) scotch yoke data; HKC ET/HP series catalogues; Rotork Fluid Power Actuators Explained PUB010-024

Scotch yoke and rack and pinion are not substitutes for each other: the scotch yoke puts peak torque where the valve needs it most, so for the same bore and pressure it develops more torque and uses less air; the rack and pinion has flat torque and a more compact body, suiting general small and medium duties.

Source: Fisher actuator technical data (G series scotch yoke, Emerson/Bettis); HKC pneumatic actuator manual (ET heavy-duty, HP series including scotch yoke); Rotork general principle data sourced below.

Pneumatic actuator appearance reference
Pneumatic actuator appearance reference, not the actual model shown; parameters subject to official catalogue

II. Working Principle

TypeActionFeature
Single-acting (spring return)Air drives the piston to rotate the yoke to the open position and compress the springs; on air failure the springs rotate the yoke to the fail positionDefined fail position with a separate spring module
Double-acting (DA)Both open and close strokes are air-driven, with no springMore compact, holds last position on air failure
Symmetric yokePeak torque similar at both endsBalanced curve, suitable for ball and plug valves
Canted yokeYoke angle shifts the peak toward one end of travelFor higher break-to-open torque, can reduce actuator size

This data comes from online searches, source: https://www.rotork.com/uploads/documents-versions/24733/1/pub010-024-00_0516.pdf (Rotork Fluid Power Actuators Explained PUB010-024: scotch yoke principle, U-shaped torque curve, symmetric and canted yokes). A scotch yoke only provides 90 degree rotation and is not suitable for three-way valves; sliding friction and high contact stress at the pin and slot are the main wear sources.

This data comes from online searches, source: Rotork Fluid Systems Fluid Power Actuators Explained PUB010-024 (URL above). Principles and limitations are subject to Rotork official data.

III. Torque Characteristic and Calculation

ItemFormula / basisNote
Basic torqueT = p x A x d (d is distance from force application to rotation center)p is air pressure, A piston area, d varies with angle
Torque curved largest at both ends, smallest at midpoint, giving a U shapePeak-to-minimum ratio about 1.4-1.6 to 1 (online data)
Sizing valuesDA catalogues give breakaway (max) and running (min)Check opening/seating and mid-stroke separately
Spring-return checkCheck both ends of air stroke and spring stroke; use the weakest spring positionSpring force varies with travel, never use a single nominal value
Safety factorT_act(theta) >= SF x T_valve(theta) over the full strokeAlso verify actuator output does not exceed MAST

This data comes from online searches, sources: https://assuredautomation.com/news-and-training/scotch-yoke-piston-actuators/ (Assured Automation scotch yoke primer, torque formula T = p x A x distance) and https://actuationvalve.co.uk/rack-and-pinion-vs-scotch-yoke-pneumatic-actuators-how-to-choose (scotch yoke peak-to-minimum ratio 1.4-1.6 to 1). Formulas are general principles; actual torque must come from the manufacturer table.

This data comes from online searches, sources: Assured Automation and Actuation Valve technical articles (URLs above); Rotork PUB010-024 gives the same torque definition. Values are general engineering bases, not manufacturer guarantees.

IV. Comparison with Rack & Pinion

DimensionScotch YokeRack & Pinion
Torque curveU-shaped, peaks at ends, dips in middleNearly constant
Best-fit valveLarge ball and plug valves, pipeline valves, ESDButterfly valves, small ball and plug valves, general service
Output for same boreGenerally higher, lower air consumptionLower but more compact
Modulating behaviorMid-stroke torque dip can interact with positioner gainMore linear, easier to tune
Rotation90 degrees onlyCan be 90 degrees or larger
Main wearSlot and pin friction, high contact stressLess rack and pinion mesh wear

This data comes from online searches, sources: https://actuationvalve.co.uk/rack-and-pinion-vs-scotch-yoke-pneumatic-actuators-how-to-choose and https://omansevenstar.com/pneumatic-actuator-sizing-torque-guide (torque curves, application ranges and selection differences). Another public catalogue (Assured Automation P series) states a cycle life up to 1,000,000, DIN/ISO 5211 (F03-F16) and NAMUR mounting, and both double-acting and spring-return versions, source: https://assuredautomation.com/news-and-training/scotch-yoke-piston-actuators/ .

This data comes from online searches, sources: Actuation Valve, Seven Star sizing guide and the official catalogue in the previous section (URLs above). Parameters and approvals are subject to official catalogues.

V. Selection Guide and Common Models

Selection guide: Follow "define valve torque curve, define DA/SR and fail direction, define symmetric or canted yoke, check torque at both ends, set interface and accessories". Core red lines: (1) the advantage of a scotch yoke is high end torque, so check 0 degrees, 90 degrees and the running point separately; (2) DA catalogues give breakaway and running values, never size from a single value; (3) a canted yoke suits duties needing higher break-to-open torque and can reduce actuator size; (4) scotch yoke suits only 90 degree rotation and cannot be used on three-way valves; (5) web-derived data is sourced in place, with parameters and SIL/ATEX approvals subject to official catalogues.

Common models: Fisher G series (Emerson/Bettis scotch yoke, formerly Robotarm II); HKC ET heavy-duty pneumatic actuators (90 degree ETS / linear ETL) and HP series scotch yoke type; Rotork GP/GH scotch yoke actuators; symmetric and canted yoke series from other makers. Full order codes and torque tables are subject to official catalogues.

If you are selecting an actuator for a large ball valve, plug valve or ESD valve, or want to decide whether a scotch yoke is better than a rack and pinion, please feel free to contact us. We can check the model together against your valve torque curve, fail direction and safety factor.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.