| Rotork / AUMA Electric Actuators - Technical Data & Selection | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Release time:2026-11-22 09:38:23 | Views: | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
An electric actuator converts electrical energy into linear thrust or rotary torque for a valve and is suitable where there is no instrument air, where precise travel control is needed, or where fieldbus integration is required. Rotork and AUMA are two independent electric actuator brands. This article compiles publicly available official data for their multi-turn and part-turn products and gives the selection basis for duty, torque and speed. All data below comes from online searches, with sources noted in each section. I. Product Positioning
The two brands have different strengths: the Rotork IQ3 emphasizes non-intrusive commissioning, absolute encoder position retention and a Bluetooth setting tool, while the AUMA SA emphasizes modularity, a wide torque range and diagnostics/fieldbus integration through AC actuator controls. Both must be sized to the actual valve torque demand, not by brand alone. This data comes from online searches, sources: https://www.rotork.com/uploads/documents-versions/42883/1/pub002-038-00_0618.pdf ; https://media.rotork.com/api/public/content/pub002-407-000526iq3prorangeflyer2-page-pdf-sjyrvee8sto4j92j7czy.pdf ; https://www.auma.com/en_GB/products/product-p35477 . Rotork and AUMA are independent brands; data is cited only from each brand's own official site.
II. Rotork IQ3 / IQT3 Technical Data
This data comes from online searches, sources: https://media.rotork.com/api/public/content/pub002-407-000526iq3prorangeflyer2-page-pdf-sjyrvee8sto4j92j7czy.pdf (IQ3 Pro Range Flyer) and https://www.rotork.com/uploads/documents-versions/42883/1/pub002-038-00_0618.pdf (IQ Range IQ3 catalogue). The IQ3 uses a contactless absolute encoder capable of measuring up to 8,000 output turns and retains valve position even without power. This data comes from online searches, sources: Rotork IQ3 Pro Range Flyer (PUB002-407) and IQ3 data sheet (PUB002-038), URLs above. Specific order configurations and certificates are subject to Rotork official manuals. III. AUMA SA / SAR Technical Data
This data comes from online searches, source: https://www.auma.com/en_GB/products/product-p35477 (AUMA official SA product page). The AUMA SAEx explosion-protected version has a torque range of 10-16000 Nm, IP68, ATEX Ex db eb IIC / Ex db IIC and Ex tb IIIC; the exact Ex marking is subject to the AUMA product page and certificates. This data comes from online searches, sources: AUMA official SA product page https://www.auma.com/en_GB/products/product-p35477 and SAEx product page. Rotork and AUMA data are taken only from each brand's own official site and are not cross-referenced. IV. Selection Calculation and Key Points
Selection sequence: (1) define the valve type and full-stroke torque curve; (2) decide multi-turn or 90 degree part-turn (large 90 degree valves often need a worm or spur gearbox); (3) select the torque rating by T_req and SF; (4) select on-off or modulating by duty; (5) set electrical configuration by site supply and fieldbus; (6) set Ex form and certificate by area classification; (7) verify mechanical interface, handwheel and torque limit setting. Torque safety factors, stroke time and duty are general engineering bases; Rotork/AUMA parameters and certificates are subject to their own official manuals. No values are invented. V. Selection Guide and Common ModelsSelection guide: Follow "define valve torque, define rotary form, define torque rating, define duty, define electrical and fieldbus, define Ex and interfaces". Core red lines: (1) Rotork and AUMA are independent brands and data must be cited only from each own official site; (2) torque must be based on the valve manufacturer's actual duty value plus a safety factor and must not exceed MAST; (3) distinguish on-off duty S2/S3 from modulating S4/S5, which have different start rates; (4) Ex forms and SIL approvals are subject to official certificates; if unavailable write "confirm by inquiry". Common models: Rotork IQ3 Pro (multi-turn, 14-3000 Nm), IQT3 Pro (part-turn, 125-3000 Nm), IQ3S/IQ3D/IQ3M variants; AUMA SA (multi-turn, 10-32000 Nm), SAR (modulating), SQ (part-turn), SAEx (Ex, 10-16000 Nm), plus GST/GK gearbox solutions for 90 degree duty. Full order codes are subject to official manuals. If you are selecting an electric actuator for a valve, or want to decide between multi-turn and part-turn or to match the torque rating and duty, please feel free to contact us. We can check the model together against your valve torque curve, power supply and fieldbus requirements. Orders & InquiriesBaoman Industrial Technology (Chengdu) Co., LtdTel: +86 028-60220547 | Email: info@bit-cd.com Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry. |

简体中文
ENGLISH
