Home » Service & Support » Technical Documentation
Quick Exhaust Valves - Working Principle & Selection
Release time:2026-11-22 09:38:23 | Views:

A quick exhaust valve is installed near the port of a cylinder or actuator and vents the exhaust gas directly to atmosphere at the exhaust stroke, instead of routing it back through a long line and a directional valve, greatly increasing the travel speed. Using data from SMC AQ series and SAMSON 3711, this article explains the principle, flow sizing and installation points.

I. Product Positioning

ItemDescription
Product nameQuick Exhaust Valve
Core functionShorten the exhaust path and reduce back pressure to increase the return speed of cylinders or actuators; common in large-bore cylinders, clamping and sorting mechanisms, and fast closing circuits
ConstructionDiaphragm or shuttle type, normally three ports: P (supply), A (to actuator), R (exhaust, can take a silencer)
Related brandsSMC AQ series; SAMSON 3711 (data sheet T 8547); similar products from most pneumatic component makers
SourceSMC pneumatic component catalogue (AQ2000/AQ3000/AQ5000 data); SAMSON accessory catalogue (3711 quick exhaust valve, T 8547)

A quick exhaust valve is not a directional control valve: it only changes the exhaust path and cannot decide which way the cylinder moves; direction is still switched by the upstream solenoid valve. It is essentially a shuttle valve that closes the exhaust port on fill and opens a large direct exhaust port on exhaust.

Source: SMC pneumatic component catalogue (AQ series data); SAMSON valve accessory catalogue (3711 quick exhaust valve, data sheet T 8547). Parameters are subject to official catalogues.

Pneumatic component appearance reference
Pneumatic component appearance reference, not the actual quick exhaust valve; parameters subject to official catalogue

II. Working Principle

ConditionElement movementAir pathEffect
Fill strokePressure at P pushes the diaphragm/spool against the exhaust port and seals RP to A into the actuatorExhaust closed, normal fill
Exhaust strokePressure at A exceeds P; the spool reverses, closing P and opening RA to R direct to atmosphereBypasses the upstream solenoid and long line; low back pressure, high speed
Static holdPressures balance and the spool resets by spring or diaphragmPorts sealed according to pressure relationActuator pressure held

The speed gain comes from exhausting close to the cylinder: hot high-pressure air no longer has to travel back through the line to the solenoid valve, so path resistance drops sharply. It suits duties where the return stroke must be fast but the fill stroke need not be; when both directions must be fast, fit valves at both ends or use a large-bore solenoid plus a high-flow booster.

The principle is a general pneumatic description; specific sealing structure, cracking pressure and mounting orientation are subject to official catalogues.

III. Main Data (SMC AQ Series)

ModelPortInlet flowExhaust flowTemperature and pressure
AQ2000-N02NPT1/41300 L/min1300 L/min5 to 60 C; 0.05-1.0 MPa
AQ3000-N03NPT3/83300 L/min3800 L/min5 to 60 C; 0.05-1.0 MPa
AQ5000-N04NPT1/25700 L/min6300 L/min5 to 60 C; 0.05-1.0 MPa
AQ5000-N06NPT3/49000 L/min10000 L/min5 to 60 C; 0.05-1.0 MPa
AQ2000/3000/5000-Nxx-LNPT1/4 to 3/4Same as standardSame as standardLow-temperature -30 to 60 C

The SAMSON 3711 quick exhaust valve belongs to its valve accessory range (data sheet T 8547), alongside the 3709 pneumatic lock valve, 3710 reverse booster and 3755 pneumatic booster. Test conditions differ between brands, so unify pressure and drop conditions before comparing flow figures.

Source: SMC AQ series quick exhaust valve catalogue (inlet/exhaust flow by port, temperature and pressure); SAMSON valve accessory catalogue (3711, data sheet T 8547).

IV. Sizing Calculation and Installation

ItemFormula / basisNote
Exhaust flow demandQ_exh approximately V_act x (P_act - P_atm) / (t_exh x P_abs)Estimated from cylinder volume and required exhaust time
Port sizeSelect from the flow curve by Q_exh and allowable back pressureExhaust line bore must not be smaller than the valve exhaust port
LocationMount directly on the cylinder/actuator port or as close as possibleMounting on the solenoid valve is far less effective
Exhaust treatmentFit a silencer or connect to an exhaust manifoldSilencer back pressure reduces acceleration and must be included
Safety circuitEvaluate together with a lock-up valve / air tank for fail-lock dutiesA quick exhaust valve accelerates venting and may affect holding

Installation points: (1) do not reverse ports P, A and R; (2) mount close to the cylinder or the flow gain is lost in line resistance; (3) point the exhaust down or protect it against rain and debris, and check silencer back pressure; (4) in cold service use the low-temperature version (-30 C) and prevent ice at the exhaust; (5) use with caution in fail-lock circuits because fast venting may prevent the position from being held.

Formulas are general engineering estimates, not manufacturer guarantees; final selection is subject to SMC and SAMSON official catalogues and actual piping. No values are invented.

V. Selection Guide and Common Models

Selection guide: Follow "define the speed target, calculate exhaust flow, set port and flow, set temperature and ports, verify silencer and location". Core red lines: (1) a quick exhaust valve only changes the exhaust path and does not provide direction control, so it cannot replace a solenoid valve; (2) flow must be selected on the catalogue curve and allowable back pressure, including silencer back pressure; (3) it must be mounted close to the cylinder, since mounting upstream at the solenoid gives limited benefit; (4) in fail-lock duties evaluate the effect on hold time, with parameters and approvals subject to official catalogues; if unavailable write "confirm by inquiry".

Common models: SMC AQ2000-N02 (NPT1/4), AQ3000-N03 (NPT3/8), AQ5000-N04 (NPT1/2), AQ5000-N06 (NPT3/4), plus the L low-temperature versions; SAMSON 3711 quick exhaust valve (data sheet T 8547). Full order codes are subject to official catalogues.

If you are increasing the return speed of a cylinder or actuator, or want to verify the quick exhaust valve size, mounting position or silencer back pressure, please feel free to contact us. We can check the model and installation together against your cylinder volume, exhaust time and piping conditions.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.