Home » Service & Support » Technical Documentation
Air Service Units (Filter/Regulator/Lubricator) - Working Principle & Selection
Release time:2026-11-22 09:38:23 | Views:

An air service unit (FRL, Filter-Regulator-Lubricator) connects filtration, regulation and lubrication in series in the direction of flow, and is the standard front end for pneumatic actuators and cylinders. This article explains, in plain language plus data from SMC AC series and Rotork Midland 3500 series catalogues, what each unit does, how it is selected and where it is installed, and gives the combination order and key points.

I. Product Positioning

ItemDescription
Product nameAir service unit (FRL), also called filter-regulator-lubricator combination
ArrangementFilter (F) then Regulator (R) then Lubricator (L), in flow direction; many duties use a combined filter regulator (FR) plus lubricator, forming a two-piece unit
Core functionRemove water and particles, stabilize supply pressure, meter lubricating oil as needed, extending the life of actuators and cylinders
Typical usersPneumatic actuators, cylinders, pneumatic instruments, valve islands requiring oil-mist lubrication
SourceSMC AC series air service unit catalogue; Rotork Midland 3500 series air preparation unit data

An FRL is not three parts arbitrarily connected. The filter must come first to protect the regulator and lubricator; the regulator sits in the middle so the lubricator sees a stable pressure; the lubricator comes last so the mist is carried directly to the actuator. Reversing the order causes unstable oil feed, early element clogging or pressure fluctuation.

Source: SMC air service unit catalogue (AC20/AC30/AC40 data); Rotork Midland 3500 series air preparation unit data. Parameters are subject to official catalogues.

Air service unit appearance reference
Filter regulator appearance reference, not the actual model shown; parameters subject to official catalogue

II. Working Principle of the Three Units

UnitFunctionKey structure and process
Filter (F)Separate water droplets and solid particlesAir enters tangentially and spins; centrifugal force throws condensate and dirt to the bowl, air passes through the element, and water drains via manual or automatic drain
Regulator (R)Hold a set outlet pressure from a fluctuating inletThe diaphragm senses outlet pressure and balances against the setting spring; when outlet falls the port opens, when it rises the port closes or vents
Lubricator (L)Atomize oil into the air stream for downstream lubricationA venturi creates a pressure drop that draws oil from the bowl through a drip tube and atomizes it; units with a flow sensor adjust oil rate with air consumption

Whether a lubricator is needed depends on downstream equipment: most modern cylinders and actuators are pre-lubricated and require oil-free air, in which case adding oil mist washes out grease and contaminates positioners and solenoid valves. Only older cylinders or centralized lubrication circuits that explicitly call for oil mist need the L unit. Therefore the common arrangement in practice is the two-piece FR rather than a full FRL.

The principles are general engineering descriptions; specific construction, relieving type (self-relieving / non-relieving) and oil-feed behavior are subject to official catalogues.

III. Main Technical Data

ItemSMC AC20/30/40 FRLRotork Midland 3500 series (3/4, 1 in)
PortNPT1/4 (AC20/30), NPT3/8 (AC30/40), etc.FR / filter / regulator 3/4, 1 in NPT; lubricator 1/2 in NPT
Rated flowAC20 about 800 L/min, AC30 about 1500 L/min (per catalogue conditions)FR / regulator 7800 L/min; filter 10020 L/min (7 bar inlet conditions)
Regulation range0.05-0.85 MPa0.5-2 / 4 / 7 / 10 bar steps
Filtration5 umStandard 40 um, 5 um optional (suffix 05)
Bowl materialMetal / polycarbonate options316L stainless with sight glass
Temperature-5 to 60 C (standard)-20 to +80 C; low-temperature version -50 to +80 C

Flow figures are measured under stated conditions (for Midland, 7 bar inlet, 6 bar secondary, 1 bar drop), so numbers from different brands and port sizes cannot be compared directly. Calculate air demand first, then compare flow curves under the same test conditions.

Source: SMC air service unit catalogue (AC20A/AC30A FRL data); Rotork Midland 3500 series air preparation data (flow test conditions, regulation steps, element grades).

IV. Combinations and Installation Points

CombinationApplicationNote
F + R + L (full FRL)Cylinders / valve islands explicitly requiring oil mistLubricator must be last, close to the consumer
FR (filter regulator)Modern actuator and positioner supply (most common)Usually oil-free dry air required; no lubricator
Separate F + RLarge air cabinets needing independent element and regulatorCheck bowl capacity and drain style separately
FR + air tank + lock-up valveFail-lock or fast-action circuitsSize the tank by actuator volume and hold time

Installation points: (1) arrow on the body must follow flow direction, reverse mounting defeats separation and oil feed; (2) mount close to the consumer, with the shortest possible line from lubricator to actuator; (3) leave service space below the drain and keep automatic drains above freezing or use a low-temperature version; (4) supply pressure must exceed the required outlet upper limit by at least 0.5 bar and stay below the unit maximum inlet; (5) in cold service control the dew point to prevent ice.

Installation points are general engineering practice; orientation, allowable pressure and temperature are subject to official catalogues.

V. Selection Guide and Common Models

Selection guide: Follow "confirm whether oil mist is needed, calculate air demand, set port and flow, set element grade and drain, set regulation step and material, verify ports and approvals". Core red lines: (1) verify first whether the downstream requires oil-free air, since most modern actuators must not have a lubricator; (2) choose element grade, bowl material and drain style by service, using 316L for corrosive media; (3) compare flow only under the same catalogue test conditions, never across brands by raw numbers; (4) explosion protection and ATEX approvals are subject to official certificates; when unavailable write "confirm by inquiry".

Common models: SMC AC20A / AC30A / AC40A FRL units (AW + AL combination) and AW series filter regulators; Rotork Midland 3500 series 3/4 in and 1 in air preparation units (FRM/FRA filter regulators, FLM/FLA filters, PRV/PRN regulators, LUB lubricators). Full order codes are subject to official catalogues.

If you are selecting an air service unit for a cylinder or actuator, or want to decide between a two-piece FR and a full FRL or whether a lubricator is needed, please feel free to contact us. We can check the combination and model together against your air demand, space and air quality requirements.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.