Home » Service & Support » Technical Documentation
TOPWORX - Valve Position Feedback Signal Types (SPDT / NAMUR / Analog) Selection
Release time:2026-11-22 09:38:23 | Views:

TOPWORX valve position feedback signals fall into four groups: discrete switching (SPDT / DPDT mechanical or GO Switch dry contact), intrinsically safe NAMUR, analog (4-20 mA / HART / FF / PA) and fieldbus (AS-i, Profibus DP, DeviceNet, WirelessHART). The signal type is set by order code digit 2 and constrained by digit 3 area classification. This article compares principles, electrical ratings, compatibility limits and application scenarios.

I. Product Positioning and Signal Categories

ItemDescription
BrandTOPWORX (an Emerson brand)
ProductsD series DXP / DXR / DXS, T series TXP / TXS / TVA / TVP and TV series position feedback switches / transmitters
Discrete switchingMechanical SPDT / DPDT (M / T / K), GO Switch dry contact (L / Z), proximity (P / R / PN / PS)
IS NAMURE2 / E4 (p+f NJ2+V3-N), 8 VDC, below 1 mA / above 3 mA
Analog4-20 mA position transmitter (X), 4-20 mA plus HART (H), FF / PA transmitters
FieldbusAS-i, Profibus DP, DeviceNet, FOUNDATION Fieldbus, WirelessHART (4310)
SourceTopWorx discrete valve controller product manual (TOPWORX.pdf)

Signal type must be cross-checked with area classification (digit 3): intrinsic safety class 0 cannot use AS / DN / ES; non-incendive class 2 only allows L / Z / P / AS / FF / DN and similar.

Source: TopWorx official discrete valve controller product manual (bus / sensor tables 1.6-1.7). Brand ownership: TOPWORX belongs to Emerson.

TOPWORX limit switch illustration
TOPWORX limit switch illustration; for illustration only, not the actual model; parameters subject to the official data sheet

II. Three Core Signal Types: Principles and Comparison

DimensionSPDT / dry contactNAMURAnalog 4-20 mA / HART
OutputPassive mechanical / dry contact on-off, two statesTwo-wire inductive, 1 mA / 3 mA two-state currentContinuous current proportional to position, optional HART superimposed
PowerNone required (dry contact)8 VDC supplied by barrier / isolator8.5-34 VDC loop-powered transmitter
Typical codesL2 / L4, M2 / M4 / M6, T2, K2E2 / E4X / H
Rating / loadGO Switch 4 A/120 VAC, 3 A/24 VDC; mechanical 15 A/120 VACRequires NAMUR barrier, weak load capabilityCompliance voltage and loop resistance must be checked
IS suitabilityDry contact is naturally suited to IS loopsStandard intrinsically safe signal (Ex ia IIC)Requires IS barrier with voltage / resistance verification
InformationOpen / closed two statesOpen / closed plus line fault monitoringContinuous position plus diagnostics (HART / NE107)
ApplicationsDCS / PLC discrete inputs, interlocksHazardous-area IS discrete inputsContinuous position, remote calibration and diagnostics

Source: TopWorx official discrete valve controller product manual (sensor electrical ratings 1.6 and NAMUR 8 VDC parameters).

III. Sensor / Signal Codes and Electrical Ratings

CodeTypeRating / description
L / L2 / L4GO Switch dry contact SPDT4 A/120 VAC, 3 A/24 VDC, intrinsically safe
Z2 / Z4GO Switch dry contact DPDTSealed double-pole double-throw contacts
M2 / M4 / M6Mechanical SPDT15 A/120 VAC; area classification cannot be 2
P / PN / PSProximity switchP max 3 A; PN max 1 A; PS max 250 mA
R2 / R4Low-current proximity SPDT0.2 A/30 VDC
E2 / E4Inductive NAMUR (p+f NJ2+V3-N)8 VDC; below 1 mA when detected, above 3 mA when not detected
X / H4-20 mA position transmitter / HART8.5-34 VDC; HART version is H
12PNP N/O inductive proximity10-30 VDC, 15 mA consumption, 0-200 mA operating current; area classification cannot be 0

When selecting an external NAMUR barrier / isolator, confirm compliance with standards such as NAMUR NE43; for analog signals with HART, confirm the barrier passes the HART frequency band. Switching loads must not exceed ratings or contact life will be shortened.

Source: TopWorx official discrete valve controller product manual (sensor electrical ratings 1.6); NAMUR NE43.

IV. Bus and Protocol Signals

Code / protocolTechnical dataArea classification constraint
FF / FL / FP (FOUNDATION Fieldbus)Factory (2)DI+(1)DO+(1)AI+(1)PID, up to 10 additional blocks; 17 mA supply; ITK 6.0 and NE107 diagnosticsClass 2 allowed; class 0 possible subject to certificate
DN (DeviceNet)12-32 VDC; 3 inputs + 2 outputs + 1 analog input; on-board diagnosticsArea classification cannot be 0
AS (AS-i 2.1)Up to 4 discrete inputs + 3 discrete outputs; handheld auto-calibrationArea classification cannot be 0; class 2 allowed
PB (Profibus DP V0)4 discrete inputs + 2 discrete outputs; warning LEDArea classification must be 1 / C / W
H (HART / 4-20 mA)Two-wire position transmitter proportional to position; remote calibration, dead-band detection and over-range alarmsIntrinsically safe class 0 requires a HART-compatible barrier
4310 WirelessHARTIntrinsically safe wireless position monitor; self-organizing network; up to 100 devices per gateway; 75 m indoor / 200 m outdoorPer certificate and project specification

Bus signals suit digital systems needing multiple variables and diagnostics; dry contacts / NAMUR suit simple interlocks. Before selection, confirm that the DCS / PLC has the corresponding bus interface and function-block license.

Source: TopWorx official discrete valve controller product manual (SCM bus network selection 1.7).

V. Application-Based Selection and Compatibility Red Lines

ApplicationRecommended signalNote
Ordinary DCS discrete input / interlockL2 / L4 GO Switch dry contact or M mechanical SPDTCheck load current and NO/NC logic; mechanical switches cannot be area class 2
Zone 0 IS discrete inputE2 / E4 NAMUR or L / Z dry contact plus barrierClass 0 cannot use AS / DN / ES; match Ui/Ii/Pi/Ci/Li
Continuous position display / diagnosticsX / H (4-20 mA / HART)Check compliance voltage and loop resistance; HART barrier must pass HART band
Digital bus architectureFF / PB / AS / DNCheck digit 3: PB must be 1/C/W; AS and DN cannot be 0
ESD / PST partial stroke testES with GO Switch, SIL-3Area classification cannot be 0 or 2

Red lines: 1. signal type is set by digit 2 and area classification by digit 3, and both must be checked together; 2. Ex ia intrinsic safety is not Ex d flameproof enclosure, and where unavailable write "please consult for confirmation"; 3. load mismatch shortens contact life, and analog loops require voltage / resistance checks; 4. specific certifications and options are subject to www.topworx.com official data sheets and certificates, and order codes are not invented.

Source: TopWorx official discrete valve controller product manual (sensor and bus tables 1.6-1.7 and area classification 1.3.3/1.4.2).

VI. Selection Guide and Common Models

Selection guide: First split by control system interface: with only DI channels and simple open / closed needs, select L / Z dry contacts or E NAMUR for hazardous-area intrinsic safety; for continuous position and diagnostics select X / H (4-20 mA / HART); for a digital DCS select FF / PB / AS / DN. Then cross-check digit 3 compatibility (class 0 cannot use AS/DN/ES, class 2 only L/Z/P/AS/FF/DN, PB must be 1/C/W) and verify barrier and load parameters. Ex ia and Ex d are strictly distinguished.

Common models: Discrete: L2 / L4, Z2 / Z4, M2 / M4 / M6, T2, K2, P / R; NAMUR: E2 / E4; analog: X / H; bus: FF / FL / FP, PB, AS, DN, 4310 WirelessHART; safety: ES (SIL-3).

If you are selecting a position feedback signal for a DCS / PLC, or want to verify the compatibility and order codes of NAMUR, dry contact and 4-20 mA, please feel free to contact us. We can confirm the signal type and code against the control system interface, area certification and load conditions.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.