Home » Service & Support » Technical Documentation
SAMSON 3730-0 Positioner - Technical Data & Ordering Code (16-digit)
Release time:2026-11-22 09:38:23 | Views:

The SAMSON 3730-0 is the non-communication basic control model of the 3730 family of electro-pneumatic positioners. It uses purely mechanical control without a microprocessor to correlate the 4-20 mA input with valve stem travel. This article covers its technical data, the digit-by-digit 16-position order code, the boundaries against 3730-1/2/3/4/5/6 and the 3731 series, plus intrinsic safety and mounting points.

I. Product Positioning

ItemDescription
BrandSAMSON (SAMSON AG, independent group)
Series / modelBasic 3730 family model: 3730-0 (no communication, no microprocessor, purely mechanical control)
Control principleForce balance / mechanical comparison, no digital microprocessor
CommunicationNone (4-20 mA two-wire set point)
Explosion protectionIntrinsic safety Ex ia, Ex nA non-sparking, dust Ex tb/tc; no Ex d flameproof enclosure in this series
Data sheetT 8384-0 EN (basic type); general document NA 0122

The 3730-0 targets applications needing only a 4-20 mA set point with cost sensitivity and no HART or fieldbus. Unlike the 3730-1 with LCD and autotune or the full-featured digital 3730-2, the 3730-0 has no digital display or self-tuning.

Source: SAMSON official data sheets T 8384-0 EN and NA 0122; family boundaries per T 8384-3/4/5 EN and T 8384-6 EN.

SAMSON 3730 series intelligent electro-pneumatic positioner
SAMSON 3730 series positioner, same-series illustration; for illustration only, not the actual model; parameters subject to the official data sheet

II. Core Technical Data

ParameterTypical value / description
Input signal4-20 mA, two-wire
Supply pressure1.4-7.0 bar
Linear travel3.6-300 mm (mounting dependent; approx. 3.6-30 mm direct-mounted on Type 3277)
Rotary angle24-100 degrees
Hysteresis / sensitivityless than or equal to 0.3% / 0.1%
Ingress protectionIP66 (with terminal box), IP67 optional
Ambient temperature-40 to +80 C (housing and Ex option dependent)
Air qualityISO 8573-1: particles class 4 / oil class 3 / humidity class 3
MountingIntegrated on Type 3277 / NAMUR (IEC 60534-6-1) / VDI/VDE 3845 and 3847

These are common 3730 platform parameters. Accuracy appears as a range of plus/minus 0.1% to 0.5% across data sheets; the actual value is subject to the official data sheet and nameplate of the specific model.

Source: SAMSON official data sheets T 8384-0 EN and NA 0122; platform parameters per T 8384-3/4/5 EN.

III. Series-by-Series Differentiation within the 3730 Family

ModelCommunicationKey featureOrder code digits
3730-0NoneNo microprocessor, purely mechanical, no LCD / autotune16
3730-1NoneBasic digital type with LCD and autotune16
3730-2NoneFull-featured digital type, parameterization plus EXPERTplus diagnostics16
3730-3HART4-20 mA plus HART, most common version16
3730-4PROFIBUS PAFieldbus, digit 4 fixed to 016
3730-5FFFF bus, Ex protection uses 4 digits, leakage sensor option16
3730-6HARTSeparate design with supply / output pressure monitoring and Ex d[ja] option14
3731-3 / 3731-5HART / FFFlameproof Ex d housing, separate order code structure15

Key boundaries: 3730-4 is PROFIBUS PA; 3730-6 is a separate 14-digit design with pressure monitoring; 3731 is flameproof Ex d. None may share the digit table of 3730-0/1/2/3/5.

Source: SAMSON official data sheets T 8384-3/4/5 EN, T 8384-6 EN and T 8387-3/5 EN.

IV. 16-Digit Order Code, Digit by Digit

PositionOptionCode and meaning (excerpt)
P1Explosion protection0 none; 1 ATEX Ex ia IIC; 3 CSA intrinsic safety; 5 dust Ex tb only; 8 Ex nA
P2Inductive limit switch0 none; 1 SJ2-SN (NC contact)
P3Solenoid valve0 none; 4 with 24 V DC
P4-P7Additional equipment (mutually exclusive group)Position transmitter 1000 (4-20 mA feedback); external position sensor; analog input; leakage sensor; binary input; 0000 none
P8Self-diagnostics4 EXPERTplus; 0 standard EXPERT (basic type normally has no diagnostic option)
P9Fixed position0
P10Housing material0 aluminum (standard); 1 stainless steel
P11-P12Fixed positions0 / 0
P13Special application0 none; 1 paint-compatible; 2 1/4 NPT exhaust port; 6 with VDI/VDE 3847 adapter; 7 additional vent hole
P14Fixed position0
P15-P16Special version (with P1) marker00 standard; 12 IECEx; 34 Ex tb; 13 Ex nA; 14 EAC; 20 2Ex ic/nA

Complete code = "3730-0" plus 16 digits. The non-communication basic type has no bus identification fixed digit (digit 4 is not forced to 0). Example: 3730-0 1000000000000000 reads as ATEX intrinsic safety, no additional equipment, standard aluminum housing; set P2=1 for discrete limit feedback. The exact digit assignment is subject to data sheet T 8384-0 EN and the official selection tool, not the 3730-3/4/5 table.

Source: SAMSON official data sheets T 8384-0 EN and NA 0122; digit structure per the published T 8384-3 EN table. Positions marked with an asterisk must be confirmed with the official ordering tool.

V. Explosion Protection, Air Supply and Mounting

ItemKey point
Ex ia is NOT Ex dThe 3730-0 offers Ex ia / Ex nA / dust protection only; where Ex d flameproof enclosure is required, select the 3731 series instead
Intrinsically safe loopWire per EN 60079-14; observe Ui/Ii/Pi/Ci/Li versus associated apparatus Uo/Io/Po/Co/Lo
Instrument airDry, oil-free and dust-free; 1.4-7.0 bar supply; flush pipework before installation
Supply pressure estimateAir-to-open (FA / ATO): required supply approximately spring range upper limit plus 0.2 bar, minimum 1.4 bar
Mounting interfacesDirect on Type 3277, NAMUR (IEC 60534-6-1), or VDI/VDE 3845 / 3847
WiringCurrent source only; M20x1.5 cable gland; 0.2-1.5 mm² terminals; follow certified terminal assignment in hazardous areas

The basic type has no pressure monitoring or fieldbus diagnostics; do not promise the pressure monitoring of the 3730-6 or the HART communication of the 3730-3.

Source: SAMSON official data sheets T 8384-0 EN and NA 0122; intrinsic safety wiring principles per EN 60079-14.

VI. Selection Guide and Common Models

Selection guide: First confirm that communication and autotune are truly unnecessary: choose the 3730-0 for plain 4-20 mA positioning, the 3730-1 for LCD and autotune, the 3730-2 for full parameterization and EXPERTplus diagnostics, and the 3730-3 / 3730-4 / 3730-5 for HART / PROFIBUS PA / FF respectively. Use the 3731 series for flameproof applications and the 3730-6 for pressure monitoring. The order code is the 16-digit result generated by the official selection tool.

Common models: 3730-0 (basic mechanical), 3730-1 (basic digital) and 3730-2 (full-featured digital); the same family also includes the 3730-3 HART, 3730-4 PROFIBUS PA, 3730-5 FF, 3730-6 (14-digit pressure monitoring) and the 3731-3 / 3731-5 flameproof models.

If you are looking for a non-communication replacement positioner for an existing valve, or want to verify the Ex position and order code of a 3730-0, please feel free to contact us. We can check the model and digit assignment against the nameplate, mounting interface and certification requirements.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.