Home » Service & Support » Technical Documentation
Masoneilan - Seat Seal Types (Metal / Soft Seat) Selection
Release time:2026-11-22 09:38:23 | Views:

The seat seal type (metal seat / soft seat) directly determines leakage class, temperature and pressure capability, and suitable media. Leakage classes are generally defined by ANSI/FCI 70-2 and IEC 60534-4. This article covers the principles of metal and soft seats, a leakage-class comparison, selection trade-offs and common cautions. Specific Masoneilan seat configurations and leakage classes are subject to official samples and model parameters are not invented.

I. Positioning and Seal Classification

ItemDescription
Brand / objectSeat seal type selection for Masoneilan (a Baker Hughes brand) control valves
Metal seatPlug and seat both metal or hard-faced, resisting high temperature, pressure and erosion
Soft seatSeat or plug with PTFE, reinforced PTFE or elastomer for tight shutoff
Leakage standardsANSI/FCI 70-2, IEC 60534-4 (control valve seat leakage)
Key trade-offTight shutoff (soft) versus temperature / pressure / erosion resistance (metal)
SourceANSI/FCI 70-2, IEC 60534-4; Masoneilan official samples (specifics subject to samples)

Seal selection first considers temperature, differential and medium, then the required leakage class: high temperature, high pressure or erosive service prefers a metal seat; clean media at moderate temperature requiring tight shutoff prefers a soft seat.

Source: ANSI/FCI 70-2, IEC 60534-4; specific model seal configurations are subject to Masoneilan official samples.

Masoneilan control valve seat seal selection reference
Masoneilan digital positioner, appearance reference only, not the actual model; parameters subject to official samples

II. Leakage Class Comparison (ANSI/FCI 70-2)

ClassAllowable leakage (general description)Typical seal
Class IIRelatively large leakage, on the order of a few percent of rated CvMetal seat, non-tight requirement
Class IIIStricter than Class II, on the order of a few tenths of a percent of rated CvMetal seat, general throttling
Class IVOn the order of 0.01% of rated Cv (general description)Metal seat, common control valve class
Class VLeakage limited by seat diameter, typically a very small allowanceMetal seat, tight metal seat
Class VIBubble-tight shutoff, bubbles per minute specified by seat diameterSoft seat (PTFE / elastomer)

The table gives general class descriptions. Specific test pressure, leakage limits and class definitions are subject to the original ANSI/FCI 70-2 and IEC 60534-4 texts and Masoneilan official samples.

Source: ANSI/FCI 70-2, IEC 60534-4. Class descriptions are general engineering practice; specific limits are subject to the standards and official samples.

III. Metal Seat Characteristics

DimensionDescription
ConstructionPlug and seat metal / hard-faced, with possible hardfacing overlay
TemperatureSuitable for high-temperature service; limits subject to material and official samples
DifferentialWithstands high differential and erosion, suitable for throttling
LeakageTypically Class II to V, not bubble-tight
Suitable mediaSteam, hot oil, particulate media, high-differential liquid
LimitationWeaker tight shutoff than soft seat; leakage may grow after erosion

Source: ANSI/FCI 70-2, IEC 60534-4 and common engineering practice; specific hardfacing materials and temperature limits are subject to Masoneilan official samples.

IV. Soft Seat Characteristics

DimensionDescription
ConstructionSeat or plug with PTFE / reinforced PTFE / elastomer sealing ring
LeakageCan achieve Class VI bubble-tight shutoff
TemperatureLimited by polymer, lower than metal seat; limits subject to material
DifferentialRisk of extrusion or deformation at high differential; verify against samples
Suitable mediaClean liquid / gas at moderate temperature requiring zero leakage
LimitationNot for high temperature, strong erosion or particulate media; fire-safety needs separate confirmation

Source: ANSI/FCI 70-2, IEC 60534-4 and common engineering practice; specific soft-seat materials and temperature / pressure limits are subject to Masoneilan official samples.

V. Selection Comparison and Cautions

DimensionMetal seatSoft seat
Leakage classClass II to VUp to Class VI
Temperature capabilityExcellentLimited by polymer
Erosion / particulate resistanceExcellentPoor
High differentialSuitableVerify extrusion risk
Typical serviceThrottling, high temperature / pressure, steamOn/off, tight shutoff, clean moderate-temperature media
Fire safetyInherently betterFire-safe design and approval to be confirmed

Cautions: 1. Leakage class and test pressure conditions must be stated together; "Class VI" alone is incomplete; 2. For high-differential soft-seat service verify anti-extrusion design; 3. For fire-safety requirements confirm fire-safe approval; 4. specific configurations are subject to official samples.

Source: ANSI/FCI 70-2, IEC 60534-4; specific model seat configurations and fire-safety approvals are subject to Masoneilan official samples.

VI. Selection Guide and Common Practice

Selection guide: Seat seal selection follows "check temperature, differential and medium first, define leakage class next, choose metal / soft seat then, verify fire-safety and special requirements". For any specific model's seal material, leakage class and temperature / pressure limits, always rely on official samples / standard texts; if unavailable write "please consult for confirmation" and do not invent model parameters.

Common practice: Choose a metal seat for throttling with high temperature / pressure or particulate media; choose a soft seat for on/off service requiring tight shutoff; when the two conflict, weigh by process priority or adopt a composite solution. Finalize with manufacturer samples and project specifications.

If you are defining the seat seal for a control valve and want to decide between metal and soft seat or how to specify the leakage class, please feel free to contact us. We can check the seal configuration and leakage class together against your temperature, differential and medium conditions.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.