The Masoneilan SVI3 is a third-generation modular digital valve positioner from Baker Hughes (formerly GE Oil & Gas). It uses HART 7 communication and a non-contact shielded magnetic travel sensor, and supports one-touch SmartCal commissioning, optional integrated IO and IEC 61508 SIL 3 functional safety. This article covers its technical data, function blocks and commissioning steps, and clearly distinguishes it from SVi1000, SVI II AP, SVI-FF (FOUNDATION Fieldbus) and the 4700.
I. Product Positioning
| Item | Description |
| Brand ownership | Masoneilan, part of Baker Hughes (formerly GE Oil & Gas), not GE process automation |
| Series / generation | SVI3, third-generation flagship modular digital positioner |
| Input & communication | 4-20 mA loop-powered + HART 7 (no FF / PROFIBUS variant in this batch) |
| Action | Single-acting (fail-safe); double acting via an added reverse amplifier |
| Travel sensing | Non-contact shielded magnetic travel sensor (no mechanical contact) |
| Travel range | Linear 0.25"-8" (6.4-200 mm); rotary 18deg-140deg |
| Safety & protection | IEC 61508 SIL 3 (EXIDA certified); IP66 / NEMA 4X; ATEX / IECEx / North American approvals |
| Source | Baker Hughes Masoneilan SVI3 Installation & Maintenance Manual Ch.6 specifications, SVI3 Quick Start Guide, SVI3 FS Specifications / Features / IOM |
All three generations share mounting brackets, and the SVI3 bracket is fully backward compatible with SVI II AP / SVi1000 for field replacement and spare-parts normalization. For FF bus applications use the SVI-FF (FF protocol type); the SVI3 described here is a HART platform and its communication capability must not be interchanged.
Source: Baker Hughes Masoneilan SVI3 Installation & Maintenance Manual Ch.6, SVI3 Quick Start Guide, SVI3 FS Specifications / Features / IOM. Brand ownership: Masoneilan belongs to Baker Hughes, not GE. Parameters are subject to official samples.

Masoneilan digital positioner, appearance reference only, not the actual model; parameters subject to official samples
II. Core Technical Data
| Parameter | Value (official sample) |
| Input signal | 4-20 mA DC, loop-powered; min 3.2 mA, max 22 mA |
| Compliance voltage | 9 Vdc at 20 mA; 11 Vdc at 4 mA |
| HART version | Revision 7 |
| Accuracy / hysteresis+deadband / repeatability | +/-0.5% FS (linear characteristic) / +/-0.3% FS / +/-0.3% FS |
| Start-up time | Power-on <150 ms; power-off no-reset <100 ms |
| Supply pressure | 1.4-8.3 bar (20-120 psi), rated 12.4 bar |
| Steady air consumption | 2.8 SLPM at 30 psi, 3.4 SLPM at 45 psi; about 40% lower than conventional positioners (manufacturer claim) |
| Flow coefficient Cv | Load 0.66 / exhaust 0.51 |
| Operating temperature | Standard -40 to +85 C; extreme type -55 to +85 C |
| Housing / weight | Chrome-plated copper-free aluminum (standard) / 316L stainless (factory order, not field upgradable); aluminum 3.3 kg, stainless 6.26 kg |
| Electrical / air ports | 2 x 1/2" NPT electrical; 2-3 x 1/4" NPT air; optional 100% exhaust collection manifold |
Source: Baker Hughes Masoneilan SVI3 Installation & Maintenance Manual Ch.6, SVI3 FS Specifications, IOM (online-supplemented port and air-consumption data, source: Baker Hughes official SVI3 manual). Parameters are subject to official samples.
III. Function Blocks and Optional IO
| Function block | Description |
| Positioning & control | Single-acting fail-safe, non-contact shielded magnetic sensing, universal linear/rotary design |
| SmartCal | One-touch setup of travel stops, air action, autotuning and preset tuning sets, with no extra tool or handheld |
| HMI | Optional high-contrast graphic LCD + keypad/buttons for hazardous areas; LCD 2 lines x 9 characters, slows below 0 C and shuts down at -20 C |
| Integrated IO (option f=2) | 1 x 4-20 mA position retransmission (NAMUR NE-43) + 2 x configurable solid-state switches (1A/30 Vdc) + 1 x configurable DI + 1 x 1 kOhm Masoneilan RPS + 1 x 1-5 V RPS input, no external accessory modules |
| Diagnostics | Basic / offline advanced / online diagnostics with NAMUR NE 107 status indication |
| Modularity & upgrade | Diagnostic level code segment a is field software upgradable; Cloning supports hot-swap replacement on demand |
| SmartRecovery | Optional pressure-control mode to maintain operation under abnormal conditions and improve availability |
| Software integration | ValVue, DTM / EDD / FDI; compatible with Emerson DeltaV & AMS, Honeywell FDM, Yokogawa PRM |
Source: Baker Hughes Masoneilan SVI3 FS Features / Communication / Setup, SVI3 IOM. Optional functions are subject to order codes and official samples.
IV. Commissioning Steps
| Step | Key action | Check |
| 1 Mounting & air check | Mount bracket and feedback per NAMUR / IEC 60534-6-1 or VDI/VDE 3845; verify dry oil-free air, 5 micron filtration | Supply within 1.4-8.3 bar, no leakage |
| 2 Power-up & communication | Connect 4-20 mA loop, confirm min 3.2 mA; identify HART 7 device with handheld / ValVue | Correct loop current and device address |
| 3 One-touch SmartCal | Run travel-stop detection, air-action setting, autotuning and preset tuning sets | No sticking, travel consistent with feedback |
| 4 IO & function check | Verify 4-20 mA retransmission, solid-state switches, DI and RPS per options; set Tight Shutoff | Each IO channel matches configuration |
| 5 Diagnostics & archive | Confirm no NAMUR NE 107 alarm, save tuning data and signature | Diagnostic status normal, records archived |
The above is a general flow based on the official quick start guide. Specific key menus, torque values and alarm codes are subject to the Baker Hughes SVI3 Quick Start Guide / Installation & Maintenance Manual.
Source: Baker Hughes Masoneilan SVI3 Quick Start Guide, SVI3 Installation & Maintenance Manual Advanced Usage / Setup chapters.
V. Distinction from Related Models
| Model | Communication | Sensing / action | Diagnostics & safety | Key difference |
| SVi1000 | HART 5 (firmware 7 available) | Contact magnetic feedback; single-acting | Standard diagnostics only, no SIL | Previous-gen economy type, NEPSI 3C intrinsic safety |
| SVI II AP (SVI2) | HART 5 / 6 | Hall-effect non-contact; single/double acting | ES / SD / AD levels | Second generation, standard/high flow, native double acting |
| SVI3 (this article) | HART 7 | Non-contact shielded magnetic; single-acting (reverse amplifier for double) | Basic / offline / online, SIL 3 | Third-gen flagship, modular, integrated IO f=2 |
| SVI-FF | FOUNDATION Fieldbus | Non-contact Hall; single/double acting | SD / AD firmware | FF bus dedicated, model code SVI-abcdefgh, not HART |
| 4700 / 4800 | Pneumatic / electro-pneumatic, no HART | Cam feedback, force balance | Mechanical, no digital diagnostics | Corrosion-resistant mechanical positioner, withdrawn after CCC expiry |
Source: Baker Hughes Masoneilan positioner selection technical files (SVI3 / SVI II AP / SVi1000 / SVI-FF / 4700 series). Related models must not share parameters or order codes.
VI. Selection Guide and Common Models
Selection guide: SVI3 selection follows "define communication and platform, define action and pneumatics, define explosion protection and IO, verify bracket compatibility". For a HART 4-20 mA loop needing modularity and SIL 3, prefer the SVI3; if double acting is required, add a reverse amplifier or move to the natively double-acting SVI II AP; if the bus is FF, the SVI-FF is mandatory and the SVI3 must not be offered as an FF type. Explosion approvals, display covers and 316L stainless housings are all order options; when unavailable or uncertain write "please consult for confirmation" and rely on the official ordering tool and certificates.
Common models: SVI3 single-acting HART 7 basic type, type with integrated IO (f=2) with 4-20 mA retransmission and switches, type with graphic LCD display cover, 316L stainless housing type, and double-acting solutions with a reverse amplifier.
If you are planning a positioner replacement or a new project and want to confirm the SVI3 HART version, IO options and explosion code, or to check its difference from SVI II AP / SVI-FF, please feel free to contact us. We can check the model and order code together against your protocol, action and approval requirements.
Orders & Inquiries
Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China
The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.