Home » Service & Support » Technical Documentation
Fisher 585C Actuator - Working Principle & Technical Data
Release time:2026-11-22 09:38:23 | Views:

Fisher 585C is a low-to-medium thrust piston actuator for small to medium sliding-stem control valves. Its double-acting design provides rigid, precise positioning, and sizes 25/50 can be fitted with a balanced spring to form the 585CR spring-return variant. This article covers its working principle, sizes and output data, service and materials, differences from related models and selection points.

I. Product Positioning

ItemDescription
BrandFisher (Emerson)
SeriesFisher 585C series piston actuators including the 585CR spring-return variant
TypePneumatic piston, linear, small to medium
Serviceeasy-e, HP, EH, 461 and other sliding-stem control valves
ActionDouble-acting; sizes 25/50 available without spring or with balanced spring (585CR)
ControlThrottling or on-off; normally with DVC6200 digital valve controller or 3600 positioner
MountingUniversal NAMUR mounting, vibration resistant, per ISA-S75.13
Main documentFisher 585C Series Piston Actuators manual D102087X012 (2013-10)

The 585C sits below the 785C (long-stroke high-thrust) in the low-to-medium thrust range; sizes 60-130 are available only without spring. For fail-safe position either select the 585CR balanced spring on sizes 25/50 or add a 377 lock-up valve system.

Source: Emerson / Fisher official product pages and Fisher 585C Series Piston Actuators manual D102087X012 (2013-10). Brand ownership: Emerson.

Fisher actuator
Fisher actuator, appearance reference only, not the actual model in this article; parameters subject to official data sheets

II. Working Principle and Construction

ItemDescription
Driving principleDouble-acting piston: cylinder pressure alternately applied on each side moves the piston and push rod for rigid, precise positioning
Spring variant585CR sizes 25/50 with bias spring: lower spring retracts the rod on air failure, upper spring extends it, giving fail-close or fail-open
Sizes25, 50, 60, 68, 80, 100, 130
Piston area168-1430 cm2 (26-221.5 in2)
Stroke29-203 mm (1.1-8 in) depending on size; standard maximum about 203 mm
Mounting kitYoke / stem diameters per manual table 3: size 25 yoke 54/71 mm, stem 9.5/12.7 mm; size 130 yoke 127 mm, stem 25.4/31.8 mm
HandwheelSizes 25/50 top-mounted; sizes 60-130 integral side-mounted
Accessories377 lock-up valve system, limit switches, position transmitter

The 585C provides low-to-medium thrust for sliding-stem valves; its double-acting construction holds the valve rigidly throughout travel, while the nickel-plated / aluminum cylinder, hard-chromed push rod and low-friction seals give long life and low air consumption.

Source: Fisher 585C Series Piston Actuators manual D102087X012. Construction description is subject to the official manual.

III. Sizes, Weights and Output Data

SizeApprox. weight (without positioner and handwheel)Piston area / output
257-8 kg (16-17 lb)Piston area about 168 cm2; 585CR spring thrust about 17,347 N (3,900 lb)
5020-22 kg (45-48 lb)585CR spring thrust about 31,358 N (6,900 lb)
6031 kg (68 lb)Springless only
6854 kg (120 lb)Springless only
80102 kg (225 lb)Springless only
100113 kg (250 lb)Springless only
130188 kg (415 lb)Springless only
Series—Family maximum thrust about 111 kN (25,000 lbf); range about 311-30,700 N

The 585CR spring thrust figures for sizes 25/50 come from manual tables 6/7 at 10.3 bar design pressure. Actual available thrust must be checked point by point against supply pressure and travel; do not simply take the maximum table value.

Source: Fisher 585C Series Piston Actuators manual D102087X012 tables 3 and 6/7; product page catalog data. Values are subject to the official manual.

IV. Service Data and Materials

ItemDescription
ItemParameter / Description
Supply pressureSizes 25-50: max 10.3 bar (150 psig), min 1.4 bar (20 psig); sizes 60-130: min 2.4 bar (35 psig), max per manual table 8
Stroke29-203 mm (1.1-8 in)
Output thrustUp to about 111 kN (25,000 lbf), depending on construction
Operating temperatureStandard (nitrile O-rings) -40 to 80 C; optional (fluorocarbon) -18 to 149 C; sizes 60-130 low-temperature option (fluorosilicone) -60 to 80 C
ActionDouble-acting, spring-return (linear); on/off, throttling, positioning
MaterialsYoke ductile iron; piston and cylinder aluminum; bolts with NCF corrosion coating; chrome-plated push rod; nitrile (standard) or fluorocarbon O-rings
ApprovalsPED, CUTR, ATEX (per product page / catalog; SIL not listed)

Air must be clean, dry and oil-free per ISA 7.0.01 / ISO 8573-1; insufficient supply pressure causes inadequate thrust and incomplete travel. For spring-return versions, net thrust must be calculated as thrust minus spring force.

Source: Fisher 585C Series Piston Actuators manual D102087X012 and official product page; air standard ISA 7.0.01 / ISO 8573-1.

V. Differences: 585C / 585CR vs 785C

Dimension585C / 585CR785C
PositioningSmall to medium sliding-stem valves, low-to-medium thrustLong-stroke high thrust, short to long stroke
Size / bore25-130; piston area 168-1430 cm2Cylinder diameter 280-685 mm (11-27 in)
Strokeabout 29-203 mm (max about 203 mm)Standard max 203 mm, special up to 610 mm
Thrustfamily max about 111 kNDouble-acting springless up to about 1600 kN; spring-return 540 kN on product page, 442 kN in manual
Supply25-50 max 10.3 bar / min 1.4 bar; 60-130 min 2.4 barMax 12 bar (174 psig)
Safety585CR spring-return; SIL not listedOptional SIL 3 Capable (IEC 61508) for SIS
DocumentD102087X012D104412X012 (Product Bulletin 61.2:785C)

When required thrust or stroke exceeds the 585C family range, move to the 785C rather than raising supply pressure beyond the manual limit; exceeding allowable pressure risks equipment damage and safety incidents.

Source: Fisher 585C manual D102087X012 and Fisher 785C Product Bulletin 61.2:785C (D104412X012, May 2022).

VI. Selection Guide and Common Models

Selection guide: First size the actuator by required thrust and stroke (25-130); then decide between springless 585C and 585CR balanced spring (sizes 25/50 only) based on fail-safe requirements; then verify supply pressure (25-50 max 10.3 bar, min 1.4 bar; 60-130 min 2.4 bar), temperature and material options; finally determine the positioner (DVC6200 or 3600), handwheel, 377 lock-up valve and limit switches. Write subject to official manual / nameplate or please consult for confirmation for unavailable size-by-size thrust and approval data.

Common models: 585C sizes 25 / 50 / 60 / 68 / 80 / 100 / 130 (double-acting, balanced spring available on 25/50); 585CR (spring-return, sizes 25/50); 785C for high thrust and long stroke.

If you are selecting feedback rods and mounting kits, verifying spring range and supply pressure, or making a preliminary Cv and size calculation, please feel free to contact us. We can work through the selection and verification together against your valve service, interface standards and installation conditions.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.