Home » Service & Support » Technical Documentation
Fisher Positioners - Feedback Rods & Mounting Kits Selection and Installation
Release time:2026-11-22 09:38:23 | Views:

The feedback rod and mounting kit determine whether the positioner correctly converts stem travel into a feedback signal, and are critical to installation quality. Fisher positioners support linear, rotary and integrated mounting following NAMUR / IEC 60534-6 and VDI/VDE 3845/3847 interfaces. This article covers mounting standards, feedback arm and kit cross references, linear and rotary installation points, and troubleshooting.

I. Product Positioning

ItemDescription
BrandFisher (Emerson)
Applicable positionersDVC2000 / DVC6200 / DVC7K / DVC6000 FIELDVUE series and mechanical positioners
MountingIntegrated, bracket-mounted, NAMUR and rotary mounting
Interface standardsIEC 60534-6-1 (NAMUR linear), IEC 60534-6-2, VDI/VDE 3845, VDI/VDE 3847, ISO 5211 (valve side)
FeedbackDVC6000 mechanical feedback arm and travel sensor; DVC6200 and DVC2000 linkage-less non-contact feedback
Key partsFeedback arm, connecting pin, coupling clamp, coupling wheel, mounting bracket, pressure gauge block
Main documentsFisher positioner installation manuals; Fisher spare parts list (official part numbers)

Mounting parts must match the positioner model, actuator type and rated travel simultaneously. The DVC6000 uses a mechanical feedback arm with model-specific travel sensor kits; the DVC6200 / DVC2000 use linkage-less feedback, so the focus shifts from arm length adjustment to mounting interface and sensor alignment.

Source: Fisher positioner installation manuals and Fisher spare parts list (official part numbers). Interface standards are subject to official manuals.

Fisher mechanical positioner installation
Fisher mechanical positioner, appearance reference only, not the actual model in this article; parameters subject to official data sheets

II. Mounting Standards and Interfaces

StandardMeaningApplies toKey point
IEC 60534-6-1 (NAMUR)Linear actuator mounting surface and connection dimensionsLinear sliding-stem actuatorsSelect components per rated travel and stem diameter
IEC 60534-6-2Extended linear mounting dimensionsLinearUsed together with 6-1
VDI/VDE 3845Rotary actuator accessory mounting surfaceBall / butterfly rotary valvesMounting surface and shaft connection must match
VDI/VDE 3847Alternative rotary mounting formRotaryNote the difference from 3845
ISO 5211Valve body to actuator flangeRotary valve sideConfirm flange designation and shaft type
Integrated mountingPositioner directly mounted on designated actuatorFisher matched actuatorsShort air lines, few leak points

When ordering, specify: positioner model, actuator model and size, rated travel or rotation, stem diameter, required mounting standard and air connections. Missing any item may result in mismatched mounting parts.

Source: mounting standard chapters of Fisher DVC2000 / DVC6200 / DVC7K manuals. Interface dimensions are subject to official manuals.

III. Feedback Arms and Kit Selection

Model / PartPart numberApplication and notes
DVC6010 travel sensor kitGG09947X012With feedback arm, standard linear
DVC6015 travel sensor kitGG09948X012With feedback arm, remote mount
DVC6020 travel sensor kitGG09949X012With feedback arm, standard rotary
DVC6025 travel sensor kitGG09950X012With feedback arm, remote rotary
DVC6015 remote magnet strip49B7986X012Remote feedback unit
DVC6025 remote magnet strip49B7987X012 / X022Long / short arm
DVC6035 remote magnet strip49B7988X012 / X022Standard / GX actuator
Mounting bracket (304 stainless)Per corresponding parts listFor rotary or bracket mounting, select by actuator
Pressure gauge blockPer corresponding parts listFor local pressure indication

DVC6200 / DVC2000 use linkage-less feedback and have no DVC6000-style feedback arm parts; their kits center on mounting surfaces and sensor brackets. Remote mounting (e.g. RM: DVC6205 + DVC6215) requires dedicated remote sensor kits with a temperature rating different from the body.

Source: Fisher spare parts list (official part numbers); RM remote mounting per DVC6200 manual D103409X012. Part numbers are subject to the latest official manual.

IV. Linear Installation Points

ItemDescription
StepKey pointRisk
1. Verify travel and stem sizeSelect components per actuator size and rated travelMismatch causes configuration over-range
2. Mount bracketFix per NAMUR / IEC 60534-6-1, tighten securelyLooseness causes feedback drift
3. Connect feedbackDVC6000: select pin position per travel table; DVC6200/2000: align linkage-less sensorWrong pin position changes actual travel
4. Connect air1/4 NPT supply, 3/8 in tubing recommended, check leaksLeakage causes consumption and response issues
5. Connect electricalWire per approval; safety barrier for intrinsically safe loopsEx ia and Ex d wiring rules differ
6. CommissionRun auto calibration and verify full travelSkipping calibration causes position deviation

When removing or adjusting feedback parts, do not force the sensor shaft with tools; move the part to its original mechanical stop first to avoid damaging the internal limit. After linear installation, check that the feedback part does not interfere with the bracket at either travel end.

Source: general installation steps in Fisher positioner installation manuals; travel tables and pin positions are subject to the corresponding official manual.

V. Rotary Installation Points

ItemDescription
StepKey pointRisk
1. Verify mounting surfaceCheck VDI/VDE 3845 / 3847 or ISO 5211Wrong surface code cannot be assembled
2. Coupling clamp and wheelFit on actuator shaft or adapter, tighten screws and washersBacklash increases dead band
3. Mind rotation directionSet coupling wheel slot per valve closed direction; PDTO / PDTC switchable in fieldWrong direction reverses valve position
4. Mount positionerFix on bracket; feedback part parallel to the long side at mid-travelNon-parallel at mid-travel causes non-linearity
5. Scale plateAttach scale pointing to valve closed positionEnables local position indication
6. CommissionVerify 45-90 degrees (or wider) travelBeyond range requires a dedicated kit

The DVC6200 supports linear 6.35-606 mm and rotary 45-90 degrees; the DVC7K bulletin lists rotary up to 45-180 degrees with a dedicated kit required for 180 degrees. Consult before exceeding the range; do not modify the feedback mechanism on your own.

Source: mounting and travel range chapters of DVC6200 manual D103409X012 and DVC7K Product Bulletin D104765X012.

VI. Troubleshooting and Selection Guide

ItemDescription
SymptomPossible causeAction
Position deviation / calibration failureWrong feedback pin position, loose bracketReposition per travel table and tighten
Increased dead bandCoupling backlash, transmission clearanceTighten coupling clamp and wheel
Abnormal air consumptionAir leak, particles clogging amplifierLocate leak and install 5 µm filter
Slow responseLow supply pressure, undersized tubingVerify supply and 3/8 in tubing
Reversed positionRotary direction set incorrectlySwitch PDTO / PDTC per manual

Selection guide: Follow the sequence determine positioner model, determine actuator type and travel / rotation, select mounting standard and kit, select feedback part and part number, verify air connections and area approval, then commission. Write subject to official manual / nameplate or please consult for confirmation for unavailable part numbers and dimensions.

Common models: DVC6000 feedback arm kits (GG0994x series) for standard and remote linear / rotary mounting; DVC6200 / DVC2000 linkage-less feedback with NAMUR / VDI-VDE 3845 mounting kits; remote mounting via RM (DVC6205 + DVC6215).

If you are selecting feedback rods and mounting kits, verifying spring range and supply pressure, or making a preliminary Cv and size calculation, please feel free to contact us. We can work through the selection and verification together against your valve service, interface standards and installation conditions.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.