Home » Service & Support » Technical Documentation
ASCO Solenoid Valves - Ex Options & Electrical Interface Selection Rules
Release time:2026-11-21 13:41:01 | Views:

The explosion protection options and electrical interfaces of ASCO (now an Emerson brand) solenoid valves are the two most confused variable groups in selection: Ex ia intrinsic safety and Ex d flameproof enclosure are different protection principles and are not interchangeable, while cable entry and port threads belong to different code segments. Using the 8327 / 531 / 325 series as examples, this article sets out Ex prefixes, electrical interfaces, voltage and power ratings item by item, and provides a ready-to-use selection rule table; where data cannot be found, "please consult for confirmation" is written and nothing is invented.

I. Scope and Basis

ItemDescription
BrandASCO (an Emerson brand; ASCO now belongs to Emerson)
Series covered8327 (direct-acting 3/2, 316L stainless), 531 (pilot spool 3/2 and 5/2, aluminum), 325 (compact direct-acting 3/2, brass)
Core topicsEx options (Ex ia / Ex d / Ex mb encapsulation / non-hazardous) and electrical interfaces (threads, connectors, leads) selection rules
Reference modelsWSNFTIS8327B312 24DC, SCG531C001MS 24DC, SCXG325B006.24/50-60.22355
Main documentsASCO official Series 327 catalog (80020GB-2018/R01), ASCO Series 531 official selection catalog, Emerson official 325 product page and distributor pages
Operating principleEach parameter has a source; unavailable items are marked "please consult for confirmation"; Ex ia is NOT Ex d

Ex prefixes and electrical interfaces are both determined by specific segments of the order code and cannot be inferred from the series number or appearance: the same 8327 series has the Ex ia WSNFTIS prefix and the Ex d WSNF / NF prefixes; the same 531 series has non-hazardous SC, intrinsic JPIS, flameproof LPKF and encapsulated EF/VCEFCM versions.

Source: ASCO official Series 327 catalog (80020GB-2018/R01, 2018 edition) sections 4.3 / 4.3.1 / 4.4; ASCO Series 531 official selection catalog; 325 series data from web-verified Emerson official and distributor pages (sources in section V).

ASCO stainless Ex solenoid valve
ASCO stainless explosion-protected solenoid valve, for selection reference only

II. Ex ia is NOT Ex d

This is the first red line in solenoid valve Ex selection. Intrinsic safety (Ex ia) limits the energy of the electrical circuit so that it cannot ignite an explosive mixture under normal or fault conditions and normally requires a certified safety barrier. Flameproof enclosure (Ex d) relies on a robust enclosure to withstand an internal explosion and flameproof joints to prevent flame transmission. Their principles, certificates, wiring and maintenance requirements all differ; they must not be interchanged or substituted.

DimensionEx ia intrinsic safetyEx d flameproof
Protection principleLimits circuit energy so it cannot igniteRobust enclosure contains internal explosion, flameproof joints stop flame
Typical marking (8327)WSNFTIS: Ex ia IIC T6 Gb, II2D Ex tb IIC Db, IP66/67WSNF / NF: Ex db IIC Gb
Coil powerIS coil 0.5W DC (24V DC only)RP power approx. 3.6 to 3.7W
External devicesCertified safety barrier requiredNo safety barrier, but cable entry must be correctly sealed
Media8327 intrinsic type limited to air and inert gasSubject to the specific model certificate and media rating
Common mistakesTreating "passive / low power" as an Ex ia certificate, or writing Ex ia and Ex d as the same protection form, are both errors; if unavailable write "please consult for confirmation"

Intrinsic loops also require checking barrier matching, gas group and temperature class; flameproof loops require checking the Ex d certificate, enclosure integrity and cable entry sealing. First determine which type of loop is present on site and then choose the corresponding prefix, never infer site requirements from the prefix.

Source: ASCO official Series 327 catalog (80020GB-2018/R01), prefix table, electrical characteristics and Ex marking table. Ex ia and Ex d are strictly distinguished.

III. Ex Prefix Comparison by Series

SeriesPrefixEx form (excerpt)Key constraint
8327WSNFTIS / WSNFISEx ia IIC T6 Gb, II2D Ex tb IIC Db, IP66/67, 316L stainless enclosureBarrier required; air and inert gas only; IS 0.5W DC
8327WSNF8327B102 / B112Ex d flameproof (Ex db IIC Gb), 316L bodyRP approx. 3.6 to 3.7W, FPM / VMQ seals
8327NF8327B112Flameproof, 316L body + aluminum flameproof coil housingVMQ low temperature approx. -40 C
531SCNon-hazardous IP65, EN 60730, epoxy molded coilSpade connector, BP basic power
531JPISEx ia IIC T6 intrinsically safe complete valvePi up to 1.5W, 24VDC only, air / inert gas only, barrier required
531LPKFEx d IIB+H2 T4 to T6 flameproof2W, low-temperature type
531EF / VCEFCMEx mb / Ex dmb encapsulation (CCC Ex)When port is 8 = NPT written as 8531
325SCXSC standard coil (IP65 non-hazardous) + X special constructionEx status of this valve unclear, please consult for confirmation

The 325 series can offer hazardous area versions per ATEX / CENELEC, but the Ex status of the delivered SCXG325B006 is not clearly documented and must be confirmed by nameplate / order and certificate; the Ex ia or Ex d prefixes of the 8327 must not be applied to the 325.

Source: ASCO official Series 327 catalog (80020GB-2018/R01); ASCO Series 531 official selection catalog. The 325 series-level Ex capability comes from the web-verified Emerson official 325 page https://www.emerson.com/en-us/catalog/asco-325 ; specific Ex status requires confirmation.

IV. Electrical Interfaces and Cable Entry Rules

The "interfaces" of a solenoid valve include at least three types: port (medium piping), cable entry (wiring inlet) and connector form. These belong to different code segments and must each be checked. The T variant of the 8327 uses a 1/2" NPT threaded entry without a cable gland, as specified in the cable entry table 4.3.1 of the catalog.

Series / modelPort connectionCable entry / connectorKey rule
WSNFTIS8327B312 24DC1/4" NPT1/2" NPT thread (T variant, no cable gland supplied)Entry method per catalog 4.3.1 cable entry table; Ex loops require suitable sealed glands
8327 European 327 designationOptional G threadDepends on prefix and variantMedia and temperature ratings subject to the 327 catalog
SCG531C001MS 24DC1/4" NAMUR direct mount + G(BSPP); external pilot 1/8"Spade connector (DIN 43650 type)Two NAMUR interface plates supplied; when port is 8 = NPT written as 8531
SCXG325B006.24/50-60.223551/8" (DN5) G ISO228/1-BSPPSC standard coil; wiring form subject to official data sheetSuffix .22355 is TPL22355 parts list and must be checked together

Cable entry thread standards (NPT and G/BSPP) are not interchangeable: NPT is a tapered pipe thread while G is a parallel pipe thread, with different sealing methods. Spade connectors and threaded entries are also different wiring schemes and must be specified in the order. Flameproof versions additionally require the cable entry to meet flameproof sealing requirements; the specific gland model requires confirmation.

Source: ASCO official Series 327 catalog (80020GB-2018/R01) section 4.3.1 cable entry table; ASCO Series 531 official selection catalog; 325 wiring form from web-verified distributor pages, subject to the official data sheet / nameplate.

V. Voltage, Power and Media Checks

Item8327 intrinsic type531 SC non-hazardous325 (delivered)
Delivered voltage24V DC (24DC)24V DC (24DC)24V AC 50-60Hz (.24/50-60)
Other voltagesIntrinsic type DC onlyAlso 230VAC versionSeries also 24 DC / 115 AC / 230 AC
PowerIS 0.5W DC (power digit 3 is LP tier, not LP 1.85W)BP basic power, low power approx. 2 to 3WNot published by manufacturer, please consult for confirmation
MediaAir, inert gas (intrinsic type limited to these two)Air, inert gas, filtered gasAir, inert gas, light oil, water
Temperature(F)VMQ low-temperature seal, minimum fluid approx. -60 C-25 to +60 C (SC prefix)Subject to official data sheet
Ingress protectionIP66 / IP67IP65 (SC prefix)Subject to official data sheet

Voltage codes must be checked character by character: .24/50-60 (24V AC 50-60Hz) and .24/DC (24V DC) are different order codes and cannot be interchanged; intrinsic types are DC only. Where power or temperature data cannot be found, write "please consult for confirmation" and nothing is invented.

Source: ASCO official Series 327 catalog (80020GB-2018/R01) electrical characteristics table; ASCO Series 531 official selection catalog. Voltage / media data for the 325 were obtained via web search: Emerson official 325 page https://www.emerson.com/en-us/catalog/asco-325 and KSCdirect model page https://kscdirect.com/itemDetail/9446465/scxg325b006-24-50-60-tpl22355-complete-sol-valve-valve-so .

VI. Selection Rule Table

The table below fixes the decision sequence for Ex options and electrical interfaces into rules that can be applied top to bottom:

StepCheck itemRuleIf uncertain
1Site loop attributeIntrinsic loop: choose Ex ia prefix (8327 WSNFTIS / 531 JPIS); flameproof application: choose Ex d prefix (8327 WSNF/NF / 531 LPKF)Please consult for confirmation
2Energy-limiting deviceEx ia requires a certified safety barrier and verification of gas group and temperature classPlease consult for confirmation
3Media compatibility8327 intrinsic and 531 JPIS limited to air and inert gas; 325 may include light oil and water but Ex status must be confirmedPlease consult for confirmation
4Port threadNPT and G(BSPP) cannot be mixed; 8327 is 1/4" NPT, 531 is 1/4" NAMUR + G, 325 is 1/8" GSubject to nameplate / order
5Cable entry8327 T variant is 1/2" NPT thread with no gland; 531 uses a spade connector; 325 subject to official data sheetPlease consult for confirmation
6Voltage and frequencyCheck 24DC / 24V AC 50-60Hz / 230VAC character by character; intrinsic type DC onlySubject to nameplate / order
7Functional safety8327 has SIL 3 capability but needs an exhaust protector; MO / MS versions are excludedPlease consult for confirmation
8Accessories and part numbers325 TPL22355 and similar parts list numbers must be checked together with the order codeSubject to the order

Red line recheck: Ex ia intrinsic safety is NOT Ex d flameproof enclosure and they must not be interchanged or substituted; prefix, thread standard and voltage code belong to different code segments and must each be verified.

Source: ASCO official Series 327 catalog (80020GB-2018/R01), ASCO Series 531 official selection catalog, Emerson official 325 product page (sources in section V). Unlisted items are not invented.

VII. Selection Guide and Common Models

Selection guide: ASCO solenoid valve Ex and electrical interface selection follows the sequence "define loop attribute (intrinsic / flameproof / non-hazardous), define prefix and certificate, verify barrier or flameproof sealing, verify media and temperature, define port thread and NAMUR mounting, define cable entry and connector, define voltage and frequency, verify SIL and parts list numbers". Core red lines: 1. Ex ia is NOT Ex d, and if unavailable write "please consult for confirmation"; 2. the 8327 intrinsic type is limited to air and inert gas with a safety barrier, while the flameproof type has RP power of approx. 3.6 to 3.7W, and the two must not be interchanged; 3. NPT and G threads cannot be mixed, and the T variant uses a 1/2" NPT entry without a gland; 4. the Ex status of the 325, the Cv / Kv of construction 006 and the seal material are not published and require confirmation; 5. the final authority is the nameplate / order and official certificates, and nothing is invented.

Common models: 8327 series WSNFTIS8327B312 24DC (intrinsic, 1/4" NPT, 1/2" NPT entry), WSNFIS8327B312 24VDC, WSNF8327B102 / B112 (Ex d), NF8327B112 24VDC; 531 series SCG531C001MS 24DC (non-hazardous SC), JPIS8531B301MO 24DC (intrinsic), VCEFCM8531G301MO 24DC (flameproof encapsulated); 325 series SCXG325B006.24/50-60.22355 (brass, 1/8" G, 24V AC) and SCXG325B006.24/DC.22355.

If you are selecting a solenoid valve for a hazardous or general-purpose application, want to decide between intrinsic safety and flameproof enclosure, need a specific cable entry and thread standard, or want to verify a voltage code and parts list number in the order code, please feel free to contact us. We can check the model and specification together against your area certification, media, interfaces and loop conditions.

Orders & Inquiries

Baoman Industrial Technology (Chengdu) Co., Ltd
Tel: +86 028-60220547 | Email: info@bit-cd.com
Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry.