| Fisher 2052 Actuator - Torque Specifications & Selection | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Release time:2026-11-21 02:05:02 | Views: | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The Fisher 2052 is a spring-and-diaphragm rotary actuator for throttling or on/off service on ball, butterfly, eccentric plug and triple-eccentric valves. It can be used with a positioner for modulating control or without one for on/off service. Its compact design and nested spring eliminate bench set, and a non-contact magnet array enables linkage-less position feedback with the DVC2000. This article covers its construction, dimensions and torque selection basis; per-position torque values are subject to the Fisher brochure 61.1:2052. I. Product Positioning
The compact design reduces valve/actuator envelope size, and the nested spring eliminates bench set. A clamping lever and single-pivot linkage grip the splined shaft to reduce lost motion, with typical accumulated dead band of a rotary control valve assembly at or below 0.5%. The fail-safe mechanism contains no aluminum (steel, cast iron, ductile iron), maintaining safety integrity under fire. Source: Fisher brochure 61.1:2052 (D103295X012 / Chinese 11745882) and instruction manual D103295X012 / 11743860. Parameters are subject to the latest official data.
II. Construction and Working Principle
The 2052 complies with ISO 5211 and can be mounted directly on non-splined shafts (square or double-D shafts with optional inserts). With a positioner it is used for throttling control; without one, for on/off service. Source: Fisher brochure 61.1:2052 (D103295X012) and the Emerson product page; construction and functions are subject to the official manual. III. Dimensions, Weight and Torque Selection Basis
Torque selection note: Output torque of the 2052 varies with actuator size (Size 1/2/3), action (double-acting or spring-return), supply pressure and spring option. A double-acting actuator delivers similar torque throughout the rotation; spring-return net torque varies with spring travel position and supply pressure. Selection must verify both that spring torque is sufficient to drive the valve and that supply pressure in the opposite direction can deliver torque at least equal to the spring. Per-position torque values are subject to the Fisher brochure 61.1:2052 (D103295X012) torque table; no invented values are listed here, and unavailable data should be referred to the official manual. Source: Fisher instruction manual D103295X012 / 11743860 and brochure 61.1:2052 (D103295X012). Weights in older bulletins differ from the current manual; the latest manual prevails. IV. Action and Operating Pressure
First size the actuator by the valve's required operating torque including a safety margin, then verify that the available supply pressure delivers the corresponding torque. If supply pressure is limited but higher torque is needed, consider a larger size or a different action rather than assuming capability beyond the brochure. Source: Fisher brochure 61.1:2052 (D103295X012), operating conditions section; pressure and torque are subject to the official manual. V. Matching Positioners and Accessories
The 2052 and 1052 are both spring-and-diaphragm rotary actuators; Fisher document D352059X012, "Replacement of Fisher 1052 Actuators with 2052", can be used for retrofit comparison. Verify mounting interface, action and torque before replacement — they must not be interchanged directly. Source: Fisher brochure 61.1:2052 (D103295X012), replacement document D352059X012 and the Emerson product page. VI. Selection Guide & Common ModelsSelection guide: Determine the action (double-acting / spring-return) and actuator size (Size 1/2/3) from valve type and required torque. Then verify that the site supply pressure delivers the corresponding torque; for spring-return, check both spring torque and reverse supply capability. Next confirm shaft diameter, ISO 5211 interface (F07/F10/F14), rotation and fail-safe direction (PDTC/PDTO). Finally select positioner, handwheel and limit switches. Per-position torque values are subject to brochure 61.1:2052; for SIL/safety applications, obtain separate certification confirmation rather than declaring it on a standard unit. Common models: Fisher 2052 Size 1 / Size 2 / Size 3, corresponding to ISO 5211 F07 / F10 / F14 interfaces; common configurations include spring-return (fail-open or fail-close) with a DVC2000/DVC6200 digital valve controller, or double-acting with a 3610J/3620J mechanical positioner. Related and similar products include the 1052 (spring-and-diaphragm rotary) and the 1061 (pneumatic pilot rotary actuator). If you have the valve's required torque and site air supply pressure and want to decide which 2052 size and action to use, please feel free to contact us. We can check the selection together against the shaft interface, fail-safe direction and positioner configuration. Orders & InquiriesBaoman Industrial Technology (Chengdu) Co., LtdTel: +86 028-60220547 | Email: info@bit-cd.com Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China The information above is not guaranteed to remain valid at all times. Subsequent changes will not be notified separately. Please confirm the latest information at the time of inquiry. |

简体中文
ENGLISH
