Bifold VBP-11-12-V Stainless Volume Booster - Arrival & Data
Baoman Industrial Technology (Chengdu) Co., Ltd. has recently received the UK BIFOLD VBP series pneumatic volume booster (VBP-11-12-V). Bifold is a UK fluid-control brand (now part of the Rotork group) and the VBP series is a piston-type volume booster that converts a low-volume pilot pressure signal into a 1:1 high-volume output; the standard body is 316L stainless steel, and the unit suits both modulating and on/off (ESD) pilot signals. Reading the arrival designation VBP-11-12-V against the official Bifold selection chart (VBP - port - ratio - seal), 11 is the 1:1 ratio code, 12 is the 3/4" NPT port code and V is the Viton seal code; a knowledge-base purchase record lists a "VBP-12-11-V pneumatic amplifier", which is the official field order and likely refers to the same configuration, although the difference in written order must be confirmed against the nameplate / purchase order. The knowledge base contains only Bifold filter-regulator material and a VBP purchase record, with no VBP technical datasheet; the specifications below were obtained via web search from the official Bifold literature and are explicitly sourced as required, for selection and spare-part verification only.
I. Arrival Photos

Arrival photo (taken by Baoman Industrial, watermarked, serial information redacted)

Arrival and unboxing detail (taken by Baoman Industrial)

Arrival and unboxing detail (taken by Baoman Industrial)

Arrival and unboxing detail (taken by Baoman Industrial)
II. Brand & Model
| Item | Specification |
|---|---|
| Brand | BIFOLD (UK, Bifold Fluidpower Ltd, now part of the Rotork group) |
| Model | VBP series piston-type volume booster; arrival designation VBP-11-12-V, with a purchase record also showing VBP-12-11-V |
| Positioning | Converts a low-volume 2-10 bar g pilot signal into a 1:1 high-volume output. The main valve moves to the all-ports-blocked rest position when outlet pressure equals pilot pressure, vents on over-pressure and recharges on under-pressure; used to speed up large actuators and ESD closing |
| Materials | Standard 316L stainless-steel body; springs in 302S26 stainless steel (Inconel X-750 available for sour gas); fasteners in 18/10 stainless steel (equivalent to Grade 316); main-valve seals in Viton as standard with low-temperature nitrile / silicone / fluorosilicone options; sensing-head seals in PTFE-encapsulated silicone |
| Arrival designation (key note) | The official selection chart order is VBP - port - ratio - seal - options - revision. The arrival marking VBP-11-12-V swaps the ratio code 11 with the port code 12; the official-order form is VBP-12-11-V. Under the official code definitions both point to the 3/4" NPT, 1:1, Viton configuration; the nameplate / purchase order governs and no other fields are assumed |
| Source status | These data were obtained via web search: the official Bifold datasheet "Volume Booster & Filter Booster Range" BFD03/8 (bifold.co.uk PDF) and the Rotork product page. The knowledge base has only a Bifold filter-regulator compilation (BFD000) and a VBP purchase record, with no VBP technical entry |
III. Technical Data
These data were obtained via web search, sourced from the official Bifold datasheet "Volume Booster & Filter Booster Range" BFD03/8 (November '11, bifold.co.uk/pdf/volume_boosters.pdf, also mirrored by finecontrols.co.uk) and the Rotork VBP product page, cross-checked with distributors' digit-by-digit explanations of order codes such as VBP-08-11-V-MD-X4. No VBP technical document was found in the knowledge base (only the "BIFOLD Filter Regulator" compilation, entry_id df6932202c4d4fe493301803e4024ab2, and a VBP-12-11-V purchase-record line), so web sources were used and are explicitly cited as required. Fields not listed in the datasheet, such as an official explanation for the swapped 11/12 order on the arrival marking, are subject to the nameplate / purchase order; no parameters or certifications are assumed.
| Item | Specification |
|---|---|
| Data obtained via web search | All VBP specifications and ordering codes below are from the official Bifold datasheet BFD03/8 and the Rotork product page; no VBP technical entry exists in the knowledge base, with sources listed in the src field |
| Digit-by-digit decoding (official field order) | VBP = piston-type volume booster, standard-service stainless-steel body; field 1 port code: 04 = 1/4", 06 = 3/8", 08 = 1/2", 12 = 3/4", 16 = 1", 24 = 1 1/2", 32 = 2" NPT; field 2 ratio code: 11 = 1:1 pilot-to-valve pressure; field 3 seal: V = Viton (standard), AL = fluorosilicone (arctic service) |
| VBP-11-12-V versus VBP-12-11-V | In the official field order, VBP-12-11-V = 3/4" NPT port, 1:1 ratio and Viton seal. The arrival marking VBP-11-12-V puts ratio 11 ahead of port 12; the code meanings give the same configuration, but it does not follow the official field order and must be confirmed with Bifold/Rotork or against the nameplate / purchase order |
| Working principle | A 2-10 bar g pilot signal applied to sensing port P opens the main valve to pass high-volume flow from inlet 1 to outlet 2. The main valve assumes the all-ports-blocked rest position when outlet pressure equals pilot pressure, opens the high-flow exhaust if outlet pressure is high and recharges if it is low, maintaining a 1:1 ratio |
| Accuracy and pressure range | Accuracy within 5% of pilot pressure (valve pressure versus pilot pressure); pilot and outlet pressure range 2-10 bar g; maximum valve inlet pressure 15 bar g (a distributor page lists 20 bar MWP; the nameplate / official data sheet governs) |
| Flow capacity Cv (standard volume booster) | 1/2": 3.2 output / 3.2 exhaust; 1": 11.0 / 11.0; 2": 50.0 / 50.0. Filter boosters are separate: 1/2" 9.3 / 3.2 and 1" 29.0 / 11.0 |
| Connections | Pilot port 1/4" NPT standard (BSPP/BSPT options); main ports offered as 1/4", 3/8", 1/2" (1/2" booster), 3/4", 1" (1" booster) or 1 1/2", 2" (2" booster) NPT, with BSPP/BSPT options; two 1/8" NPT gauge ports with one plugged as standard (1/4" NPT or BSPP/BSPT optional) |
| Operating temperature and seals | Viton standard seals: -20 to +180 C; low-temperature nitrile/silicone seals: -50 to +40 C; sensing-head seals are PTFE-encapsulated silicone as standard |
| Operating media | Air, natural gas, inert gases and sweet and sour gases; Inconel X-750 springs available for sour-gas service |
| Mounting and accessories | Mounting brackets supplied as standard; manual or auto-drain filter bowls are available to combine a filter regulator and volume booster in one unit; check valves, flow control valves and pilot-solenoid-operated versions are also available. The 1 1/2" and 2" sizes are not offered as filter boosters |
| Certification boundary | The official Bifold datasheet lists SIL 3 third-party certification to IEC 61508 Parts 1 and 2 for the VBP filter booster. The volume booster is a purely pneumatic accessory, not an electrical Ex device; hazardous-area use must be checked against the system design and product certificate, and intrinsically safe Ex ia and flameproof Ex d are not mixed on this page |
| ESD fast-closing capability | The official selection chart uses a 50-litre actuator at 5 bar set pressure with >10 bar upstream: a 1" volume booster gives approximately 1.2 s opening and 2.5 s closing at 5 bar, achieving the required closing speed without an additional poppet or quick-exhaust valve |
| Procurement corroboration | The knowledge-base purchase record "Actual Procurement Cost Record up to 2026-07-31" (entry_id a9d9ab0f051447ca99f6ac7e74d261b1) contains a "VBP-12-11-V pneumatic amplifier" line, corroborating the port/ratio/seal configuration of this arrival; no complete option suffix is given there |
These data were obtained via web search. Sources: (1) the official Bifold datasheet "Bifold Volume Booster & Filter Booster Range", document BFD03/8 (November '11), PDF at http://www.bifold.co.uk/pdf/volume_boosters.pdf (cross-checked via the finecontrols.co.uk mirror at files/pdf-manuals/bifold-pdfs/bifold-volume-boosters.pdf); (2) the Rotork VBP-04 product page at https://www.rotork.com/products/flow-pressure-control-filtration/bifold-volume-booster/vbp-04 (Bifold is now part of Rotork); (3) a distributor's digit-by-digit page at https://www.radward.co.uk/bifold/model-vbp-08 (VBP-08-11-V-MD-X4: VBP = Volume Booster Piston, 08 = 1/2" NPT, 11 = 1:1, V = Viton) and bifold.su entries for VBP-12-11-V / VBP-16-11-V, used to corroborate port/ratio/seal code meanings. The knowledge base returned only the "BIFOLD Filter Regulator" compilation (entry_id df6932202c4d4fe493301803e4024ab2, BFD000/2018) and a VBP-12-11-V purchase-record line, with no VBP technical document, so web sources were used and explicitly cited as required. Items not listed in the official datasheet or anomalies in the arrival marking are flagged; no values are assumed.
IV. Related Models
| Item | Specification |
|---|---|
| VBP-12-11-V (purchase-record form) | Most likely the same configuration as the arrival marking: 3/4" NPT, 1:1 ratio, Viton seals and a 316L stainless-steel body, written in the official field order and to be confirmed against the nameplate; sources Bifold datasheet BFD03/8 and the knowledge-base purchase record |
| VBP-08-11-V-MD-X4 | A 1/2" NPT, 1:1, Viton filter booster in the same family with manual drain and a 40-50 micron element (Cv 3.6); different from the plain volume booster here, with filter options marked -MD-X4; sources radward.co.uk and the Bifold datasheet |
| VBP-16-11-V / VBP-04 / VBP-32 | Other port sizes in the family: VBP-16 = 1" NPT (Cv 11.0), VBP-04 = 1/4" NPT and VBP-32 = 2" NPT (Cv 50.0); different port codes require re-checking flow and ESD times; source Bifold datasheet BFD03/8 |
| Bifold HIPEX series | Bifold's high-flow 2/2 exhaust valve range, used with VBP volume boosters for rapid ESD venting and available in 1/2", 1" and 2" sizes; source Bifold datasheet BFD03/8, page 11 |
| ControlAir 600 / 6000 / 6500-6600 | Alternative volume boosters from another brand; the knowledge-base document "ControlAir Amplifier Technical Data and Model Rules" (entry_id 48403c848a9c4804a578c63be72fea04) provides digit-by-digit codes and Cv comparisons. Selection requires item-by-item checks of ports, Cv and materials, and specifications are not interchangeable with the VBP |
V. Selection Guide & Common Models
Selection guide:Selection starts with the duty: the VBP is a purely pneumatic volume booster driven by a low-volume pilot signal to deliver high-volume output, used to speed up large actuators and ESD closing; it does not include regulation or filtration (filter boosters are a separate form). Then check the codes: port 12 = 3/4" NPT, ratio 11 = 1:1 and seal V = Viton (-20 to +180 C); arctic service calls for the AL fluorosilicone seal with a revised temperature range, and sour gas calls for confirmation of Inconel X-750 springs and material compatibility. Check Cv and open/close times against the actuator volume and required stroke time (the 3/4" port corresponds to the 1" booster band with Cv 11.0 in the datasheet and the exact figure should be confirmed with the manufacturer), along with pilot pressure 2-10 bar g, maximum inlet pressure 15 bar g, accuracy within 5% and the two 1/8" NPT gauge ports. For hazardous areas, confirm applicable certificates such as SIL 3 against the system design and product certificate; the volume booster itself is not an electrical Ex device and intrinsically safe and flameproof types must not be mixed. Most importantly, the arrival marking VBP-11-12-V does not follow the official field order, so confirm port size and ratio from the nameplate / purchase order before ordering or stocking. Please feel free to inquire for an item-by-item check against your actuator and service conditions.
Common models:This arrival: the UK BIFOLD VBP series pneumatic volume booster (316L stainless steel, arrival designation VBP-11-12-V, pointing under the official codes to a 3/4" NPT, 1:1, Viton configuration). These data were obtained via web search, sourced from the official Bifold datasheet BFD03/8 and the Rotork product page, for selection and spare-part verification only, not guaranteed values. The difference between the arrival marking and the official field order is subject to the nameplate / purchase order, and items not listed in the available materials are not assumed.
These are some of the configurations we supply regularly. If you are working through a selection, or would like to know about availability of these models, feel free to get in touch — we can look at the right combination together based on your operating conditions.
Disclaimer: The information above is not guaranteed to remain valid and may be modified without separate notice. Please confirm the latest information at the time of inquiry.
Ordering & Inquiry
Baoman Industrial Technology (Chengdu) Co., Ltd Address: Room 1108, Building A, Tingbiao Central Plaza, No. 158 Erxianqiao East Road, Chenghua District, Chengdu, Sichuan Province, China

简体中文
ENGLISH
